Cheshire

EV charger installation in Mold.

EV charger installation in Mold starts with the supply and where the car parks. Mold is 13 miles from our Ellesmere Port base; Flintshire counted 3,426 private plug-in cars by June 2026, 62% more than a year before.

Get a free quote Get a Mold quote
From our base
13 miles
Network
SP Manweb network
Plug-in cars, Flintshire
3,426
A Hypervolt car charger on a brick wall, its tethered cable coiled round it
A tethered charger on a brick wall, its cable coiled round the unit

In short

Most homes near the centre of Mold run a car (86% in the 2021 Census), and the plug-in count across Flintshire grew by about 62% in the year to June 2026. A home charger must be smart by law, Welsh permitted-development rules decide whether it needs planning, and the network operator is notified once it is in. The figures, with their sources.

The roof studio

Turn the house, fill the roof.

A Cheshire semi on a turntable. Drag it round, then tell it about your roof and your house — the panels, the battery, the current running through it and the numbers all move together.

01Your roof

Which way the roof faces
Roof pitch
Shading

02Your house

£120 a month
Home during the day?
Book a survey with these figures

Estimated generation

3,870

kWh a year

Estimated saving

£834

a year, saved and earned

Estimated payback

10.1

years

System size

4.40 kWp

Panels

10

Your use covered

58%

Of what the roof generates

Used in the house70% Exported30%

Worked out for a typical Cheshire roof at the pitch and aspect you picked, on a unit rate of 28p and an export rate of 6.5p — rates this tool assumes, dated September 2026, rather than any tariff you have been offered. Nothing here is a quotation: your roof, your shading and how much electricity you use while the sun is up are what the survey settles.

Take the figures with you.

Copy what the studio worked out for your roof, or send it straight to us with a survey request. None of it is a quote: the survey replaces every figure above with your own.

Book a survey with these figures How we size a system
Every assumption behind the numbers
Unit rate
28p for every unit (kWh) you’d otherwise buy from the grid.
Export rate
6.5p for every unit the house and battery can’t use and send back to the grid.
Your yearly use
Worked out from your monthly bill at the 28p unit rate, after a standing charge of about 36p a day — and never less than 1,100 kWh a year.
What a panel makes
Each panel is 440 W (0.44 kWp). A kWp makes 880 kWh a year facing south, 760 facing east–west and 620 facing north-ish. For this part of Cheshire the EU’s PVGIS model gives 951 for a south roof at a typical pitch — the studio stays below it.
Pitch
Shallow (28°) makes 95% of a typical 38° roof; steep (48°) makes 97%.
Shading
A bit of shade costs 10%; heavy shade costs 24%.
How many panels
Two rows, growing with your bill from three columns to eight — six panels up to sixteen.
How much you use yourself
The share of what the roof makes that the house uses: 30% if you’re usually out, 46% in and out, 62% usually home. A battery adds 24 points and a car charger 6, up to 86% — and never more than 62% of your whole year’s use.
Saving
The units you use yourself at 28p, plus the units you export at 6.5p.
Payback
The yearly saving set against what a system like the one you’ve built typically costs to install: a base figure, an amount for each panel, and more again for a battery or a charger. The answer is held between 4 and 25 years. The studio never shows that cost, because only a survey can price your roof — so treat the years as a rough guide, not a figure to hold us to.

Monthly and yearly sunshine for this area: PVGIS 5.2, EU Joint Research Centre. The unit rate, the export rate and the standing charge are the studio’s own assumptions, set in September 2026 — not a tariff we have quoted you. Your own rates are on your bill, and a survey works from those.

Census 2021, around the centre

Mold’s homes, cars and driveways.

Mold’s central 2 Census neighbourhoods, counted inside Flintshire, held 8,095 households in 2021.

  • 86% of households have a car or van39% have one and 48% two or more; 14% have none. Every one of those cars is a candidate for the switch, and the charger is the part that has to be planned.
  • 92% live in a house48% detached, 31% semi-detached and 13% terraced. The Census does not count driveways, but a detached or semi-detached house is where off-street parking, and a home charger, is most likely.
  • 8% live in a flatA flat with its own allocated space can still have a charger, and that is exactly who the government’s chargepoint grant is for.

Source: ONS Census 2021 (TS044, TS045, TS054) via Nomis, summed over the 2021 middle-layer neighbourhoods whose postcodes sit inside Mold’s built-up area and Flintshire.

DfT figures

Electric cars in Flintshire, and public charging around Mold.

  • 3,426 privately kept plug-in carsLicensed in Flintshire at the end of June 2026, up from 2,121 a year earlier, a rise of about 62%. 2,273 of them are fully battery electric; the rest are plug-in hybrids.
  • 166 public chargers in Clwyd EastThe parliamentary constituency that takes in Mold’s centre, on 1 July 2026, against 162 on 1 January; 50 of them are rapid, 50 kW or more.
  • 184 public chargers across FlintshireAbout 118 for every 100,000 people. A public charger is for the journey; the charging that sets the running cost happens on the drive, overnight.

Sources: DfT vehicle licensing statistics, table VEH0142 · DfT electric vehicle charging infrastructure statistics (Zapmap data), 1 July 2026. The council in more depth: the Flintshire EV guide.

PVGIS, for this town

Charging a car from a Mold roof.

Monthly output of 1 kWp facing due south at a 38° pitch, at Mold’s own coordinates, averaged over PVGIS-SARAH2 years.

  • 33Jan
  • 51Feb
  • 82Mar
  • 107Apr
  • 120May
  • 115Jun
  • 114Jul
  • 104Aug
  • 88Sep
  • 61Oct
  • 40Nov
  • 32Dec
  • Summer days can fill a carMay to July make about 37% of a Mold roof’s year. A solar-aware charger puts that surplus into the car instead of exporting it; Hypervolt’s Eco mode starts at about 1.4 kW of surplus.
  • Winter belongs to the night rateDecember and January make only about 7% of the year, so in winter the charger works the cheap overnight window instead, which is what the smart-charging rules are built around.

Modelled with the JRC’s PVGIS tool, version 5.2. A shaded roof, or one facing east or west, makes less; the roof studio above runs the same model for your own roof and bill. How a charger and the panels share the surplus: charging an EV from your own solar.

The wires

Connecting a charger to the grid in Mold.

  • A home charger is notified to the network operator. Under the Energy Networks Association’s connect-and-notify process, where the home’s maximum demand stays at 60 amps per phase or less the charger is fitted first and notified within 28 days; above that, the operator is asked first. For Mold, the operator is on the SP Manweb network.

    energynetworks.org

  • A 22 kW charger needs a three-phase supply and most UK homes are single phase, so a home charger is normally 7 kW or so; Hypervolt publishes its Home 3 Pro at 7.4 kW single phase.

    energysavingtrust.org.uk · support.hypervolt.co.uk

We send the notification for you; you do not chase it. How G98 and G99 work.

Planning

Planning rules in Mold for a home charger.

  • In Wales the 2019 rules still apply: a wall-mounted charging outlet is permitted development if it is no bigger than 0.2 cubic metres, does not face onto and sit within 2 metres of a highway, and is not on a scheduled monument; an upstand may be up to 1.6 metres, one per parking space.

    legislation.gov.uk

  • In Flintshire there are currently 32 conservation areas. Flintshire County Council’s page lists one conservation area in Mold: Mold (one of the three historic market-town centres the council lists, with Flint and Holywell). The council publishes a map of its conservation areas, and its Local Planning Guidance Note 7 covers conservation areas.

    flintshire.gov.uk

The whole picture: planning for an EV charger, England and Wales compared. And for Flintshire in particular, EV charging in Flintshire.

What the law asks of a charger

Smart charging in Mold: the rules and the tariffs.

  • Since the Electric Vehicles (Smart Charge Points) Regulations 2021, a home charger has to be smart: it comes with default charging hours set outside the weekday peaks (8 to 11 in the morning and 4 to 10 in the evening), the owner can override them, and it applies a random delay of up to ten minutes to each charge.

    legislation.gov.uk · regulation 10 · regulation 11

  • Intelligent Octopus Go is a smart EV tariff: Octopus schedules the car’s charging itself, and the whole home gets the cheap rate for six hours every night, from 23:30 to 05:30. Hypervolt says its Home 3 and Home 3 Pro can use the integration, and Octopus supports Tesla cars directly.

    octopus.energy · blog.hypervolt.co.uk

  • A tethered charger has its cable permanently attached; an untethered one has a socket and you use the car’s own cable. Every Hypervolt charger is tethered. Hypervolt publishes integrated PEN-fault protection on the Home 3 Pro, and lists it for TN-C-S, TN-S and TT earthing; whether a particular house needs anything more is settled on the survey.

    Energy Saving Trust: smart charging · Hypervolt: FAQs · Hypervolt: Home 3 Pro technical specification

More: Intelligent Octopus Go with a home charger · tethered or untethered? · choosing a home EV charger.

The charger we fit

The home charger we fit in Mold.

Hypervolt Home 3 Pro, wired from the consumer unit with load management on the incoming supply; the Tesla Wall Connector is supplied on request.

How the Home 3 Pro works, mode by mode: Hypervolt Home 3 Pro, from the people who fit it. More on our home EV charger installation page.

Straight answers

When we’d tell you not to, in Mold.

A survey that ends in “not this house” is a good survey. These are the usual reasons.

  • Nowhere off the street to parkAbout 8% of households around Mold’s centre lived in a flat in 2021, and many terraces have no drive. A charger needs its own parking space; trailing a cable over a pavement is not something we will do without the authorised cross-pavement solution the new rules require.
  • A looped or shared supplySome older houses share a supply cable with next door. The network operator has to separate it before a charger goes in, and Electricity North West says so in terms; we check the cut-out before quoting.
  • A supply already near its limitUnder connect-and-notify, a home that would go over 60 amps per phase has to ask the network first. Load management usually keeps a charger inside the limit, but if it cannot, the application comes before the install.
  • A charger facing the road within 2 metres of itWelsh rules apply in Mold: a wall charger that faces onto a highway within 2 metres of it is not permitted development. That changes where it goes, or means asking Flintshire first.

How it runs

A charger installation in Mold, step by step.

  1. CallThe car, where it parks and the consumer unit. A photo of the meter and fuse settles most of it.
  2. CheckThe supply, the earthing and the cable route confirmed on site before anything is ordered.
  3. InstallUsually half a day: mount, wire, protect the run, test, and label what we have added.
  4. Set upThe schedule, the solar mode where there are panels, and the SP Manweb network notified within the 28 days.

Costs and help

Paying for a charger in Mold.

  • The grant, and who it is forThere is no government grant for a charger at a house you own. The EV chargepoint grant is for people who rent, or who own and live in a flat, with private off-street parking: it pays 75% of buying and installing a socket up to a cap set by the government, until 31 March 2027, and only through an installer OZEV has authorised. The detail: EV charger grants in 2026.
  • What sets the price of a chargerThe supply, the length and route of the cable run, the earthing and whether load management is needed. We quote after the check, not before: what goes into the cost of a home EV charger.
  • The overnight rateA smart tariff with a cheap night window does most of the saving; the panels add to it in summer. How Intelligent Octopus Go works with a home charger.

From the Google profile

Homeowners on their chargers.

10 of our 39 Google reviews mention a car charger. Here are 6, word for word; none is located to a town, so none is claimed for Mold.

The Google profileSee them on Google →

The additional charging point fitted efficiently and promptly would highly recommend electrifyd

andrew carringtonGoogle review · June 2026

I had an EV charger installed by Electrifyd. Fantastic communication from Andre. Excellent product knowledge, quick clean and tidy job with a good turnaround time.

Highly recommended.

Kristian HortonGoogle review · May 2026

Andre was very helpful throughout the entire process. We chose the Hypervolt Pro 3 car charger and he also showed us how to use the app. Excellent service.

emma ColeGoogle review · May 2026

They were very professional and easy to deal with while installing our EV charger. They had vast knowledge and helped with other areas. I will definitely use them again.

Sarka O'NeillGoogle review · April 2026

My EV charger was installed without a hitch and in good time - a first class service.

Philip GilbertGoogle review · March 2026

I recently had a Tesla charger installed by Daniel, and I’m extremely pleased with the whole experience. From start to finish, Daniel was professional, knowledgeable, and very efficient. He explained the installation process clearly and made sure everything was set up perfectly for my Tesla.

The work was completed to a very high standard, and Daniel paid great attention to detail to ensure the charger was installed safely and neatly. He was also friendly, punctual, and happy to answer any questions I had.

I would highly recommend Daniel to anyone looking to install a Tesla charger. Excellent service and a great job. Thank you

Read it in full on Google
Daniel CurleancaGoogle review · March 2026

All the reviews, with the replies

Where we work

Home chargers across Mold: the postcodes.

A charger job in Mold covers the CH7 postcode district around the centre, from Mold: Broncoed, Mold East, Mold South, Mold West and Argoed and New Brighton. The van carries the charger, the cable and the protective devices, so a straightforward wall-mounted job is usually done in one visit.

Mold · questions

EV chargers in Mold: what people ask.

If yours isn’t here, give us a ring and ask, or see every question.

Usually not. Welsh permitted development covers a wall charger of up to 0.2 cubic metres, set back from any road it faces by at least 2 metres, away from scheduled monuments. Flintshire County Council decides anything outside that.

Yes, the local network operator is told. If the house’s peak demand is within 60 amps on each phase, we fit the charger and send the notice within 28 days; if not, the operator approves it first.

Not for a house you own. Renters, and owner-occupiers of flats who have their own parking space, can apply: it runs to 31 March 2027, pays 75% of the cost up to a cap, and has to be claimed by an OZEV-authorised installer. Our grants guide sets out who qualifies.

Yes, with a solar-aware charger. Hypervolt publishes an Eco mode that puts solar and home-battery energy first and a Super-Eco mode that uses nothing else. A south-facing roof in Mold makes about 946 kWh a year per kWp, most of it in summer.

Only where the house has three phases coming in, which is rare in British homes. A single-phase charger is normally around 7 kW, and the Hypervolt we fit is a 7.4 kW single-phase unit.

On 1 July 2026 the DfT counted 166 public chargers in the Clwyd East constituency, 50 of them 50 kW or faster, and 184 across Flintshire.

13 miles in a straight line from Ellesmere Port. The nearest towns we also cover, Neston, Wrexham, Chester, have charger pages of their own.

Data last reviewed: October 2026.

From the blog

Worth reading before a charger survey in Mold.

  • EV charging6 min read

    The best home EV charger for you: a buyer's checklist

    Not a ranking: our checklist for any home EV charger. Smart rules, cable style, 7 kW or 22 kW, solar modes, load management, PEN protection, tariffs.

    19 October 2026

  • EV charging6 min read

    EV charger grants in 2026: who qualifies and who doesn't

    The 2026 EV charger grant is for renters and flat owners with off-street parking. Who qualifies, who doesn't, how it's claimed, and the on-street grant.

    19 October 2026

  • EV charging7 min read

    EV charger installation cost: what decides it

    What decides the cost of installing an EV charger at home: your supply and main fuse, the cable run, earthing, the cable style and the paperwork.

    19 October 2026

Around here

EV chargers near Mold.

Nearest towns we cover

What we fit in Mold

Also for Mold

Start here

Get a Mold quote.

Tell us the postcode and roughly what you use. We’ll tell you honestly whether the roof is worth doing — and if it isn’t, that’s a perfectly good answer too.

Tell us about your roof

What are you after?

Or call 0330 133 6441

Thanks — we have it.

It’s with us now, and we aim to reply within a couple of hours.

  • Takes about a minute
  • You get a person, not a brochure
  • No obligation, and no visit until you ask for one